Quick Specs
- Type: Gold-plated coil pendant findings, 3/4 inch
- Size: 0.75″
- Size/Quantity: Set of 24 coil caps
- Best for: DIY crystal point pendants, spiritual jewelry making, craft vendor supply
Coil Pendant Findings and the Crystal Jewelry Craft Tradition
The coil pendant finding, sometimes called a coil bail or spiral cap, is among the most practitioner-friendly crystal jewelry components available: it requires no tools, no adhesive, and no drilling. The coil is simply pressed onto the tip of a crystal point and twisted gently to secure, creating a pendant ready to string on a cord or chain in under a minute. This format emerged as a practical solution for the crystal jewelry market, where artisans and small-shop owners needed a way to convert natural mineral points into wearable pieces without the investment in wire wrapping skills or risk of drilling damage to valuable specimens.
The 3/4 inch size is designed for slim to medium crystal points, the kind that occur most commonly in quartz varieties, selenite wands, and smaller mineral specimens. This size works well with citrine points, amethyst natural points, clear quartz generators in the one to two inch range, and small tourmaline or kyanite blades. It is a versatile size for the active crystal jeweler who works across stone types. The gold plating adds warmth and pairs naturally with the amber, orange, and golden stone palette that dominates crystal jewelry aesthetics.
Using a Set of 24 for Craft and Retail
Twenty-four coils provides a working supply that justifies setup time without excessive cost commitment. For craft fair vendors, this covers a standard display run of finished pendants with spares. For practitioners making gifts or class supplies, it means twenty-four wearable crystal pieces without the labor of wire wrapping each one. For metaphysical shops restocking their jewelry supplies, it rounds out the inventory alongside jump rings, chains, and cord without creating overstock on a single finding type.
The gold plating on these coils is a functional surface finish rather than solid gold, which is the standard for this price point across the jewelry finding market. The finish holds well under normal wear conditions but will eventually wear through at points of high friction, which is standard behavior for plated findings. Practitioners and vendors who cycle through inventory quickly will not encounter this issue; those making heirloom-quality pieces for long-term wear should consider solid brass or sterling wire-wrapped settings instead.
How to Use Gold Plated Coil Pendant Findings
How to use gold-plated coil findings to make crystal point pendants quickly without tools.
- Select and match your crystal points
Sort your crystal points and select those whose tip diameter matches the 3/4 inch coil opening. Points too thick will not seat properly; those too thin may slip out. Citrine, small clear quartz, and slim amethyst points work well.
- Seat and secure the coil on the tip
Press the open end of the coil firmly onto the crystal point tip and twist gently clockwise to tighten the spiral against the stone. No adhesive is needed for well-tapered points. Test the hold with gentle downward pressure before stringing.
- String onto a cord or chain and finish
Thread a cord, leather lace, or fine chain through the top loop of the seated coil. Adjust the length and tie or clasp the ends. The finished pendant is ready to wear or gift. Store unused coils in a sealed bag to prevent tarnish.
The Tarot Fellow Standard
I carry coil findings in gold because it is the most practical entry into crystal pendant making, and a set of twenty-four gives the active maker or small vendor a meaningful working quantity. These are honest, functional findings at a realistic price point for what they are. Find cords, chains, and complementary jewelry components in my jewelry collection, and browse loose crystal points to fill them in my crystals and gemstones section.
Frequently Asked Questions
The 3/4 inch coil suits slim to medium crystal points typically measuring one to two inches in length. Citrine points, natural clear quartz generators, small amethyst points, and slim tourmaline or kyanite blades are the best matches.
For well-tapered crystal points, a properly seated coil holds without adhesive. Twist clockwise onto the tip and test with gentle pressure before stringing. Points with blunt or irregular tips may need a small dot of jeweler’s adhesive.
Gold plating on jewelry findings will eventually wear at friction points with regular use. This is standard behavior for plated findings and differs from solid gold or gold-filled components. Wire-wrapped settings are more durable for daily wear.
Coil findings are designed for tapered crystal points. Tumbled stones, cabochons, and irregular specimens need a different setting such as a wire cage, glue bail, or bezel. The coil relies on the tapering geometry of a point to grip reliably.
Reviews
There are no reviews yet